8 Best Horizontal Band Saws for Metal Cutting 2020

horizontal band saw for metal cutting

When you are reading this, you must have a complete knowledge of horizontal band saws, especially the metal cutting ones. Though sometimes people consider it as the replacement of their regular metal cutting saw and chop saw. Whether this handy project managers manage large and small metal, wood, lumber, and more ferrous things at the same time.

If you are a hobbyist, then it must be a fresh start. So you may get overwhelmed at the stores by the collections of horizontal band saws for metal cutting. Like you, others even get involved in a battle to choose among them. Potential customers buy ones that offer the most similar to a vertical band saw. In case they are costly but conclude with a basic range of good features at the same time. All your questions regarding the horizontal band saw, you will find through this article. We bet neither to find the better one than hand-picked below. 

Would you like to take the challenge with our picked metal cutting horizontal band saw? Hope you are ready-to-go for now.

Preview
Overall Best
KAKA BS-712N, 7-inch Metal Cutting Horizontal Band Saw
Jet HBS-916W 1-1/2 HP 115-Volt/230Volt 9-Inch by 16-Inch Capacity Horizontal Band Saw
Dake SE-712 Model Standard Duty Horizontal Band Saw, 120V, 1 Phase, 63-1/2" Height x 21" Width x 56" Length
Baileigh BS-250M Hydraulic Horizontal Mitering Band Saw, 110V, 1.5hp Motor, 1" Blade, 8.93" Round Capacity
3 Speed!!! 1 HP 4 in. x 6 in. Horizontal Vertical Metal Cutting Band Saw FEDEX
SHOP FOX W1715 3/4 HP Metal Cutting Bandsaw
Product
KAKA BS-712N, 7-inch Metal Cutting Horizontal Band Saw
Jet HBS-916W 1-1/2 HP 115-Volt/230Volt 9-Inch by 16-Inch Capacity Horizontal Band Saw
Dake SE-712 Model Standard Duty Horizontal Band Saw, 120V, 1 Phase, 63-1/2" Height x 21" Width x 56" Length
Baileigh BS-250M Hydraulic Horizontal Mitering Band Saw, 110V, 1.5hp Motor, 1" Blade, 8.93" Round Capacity
3 Speed!!! 1 HP 4 in. x 6 in. Horizontal Vertical Metal Cutting Band Saw FEDEX
SHOP FOX W1715 3/4 HP Metal Cutting Bandsaw
Star Rating
-
-
-
-
-
-
Prime Status
-
-
-
-
Overall Best
Preview
KAKA BS-712N, 7-inch Metal Cutting Horizontal Band Saw
Product
KAKA BS-712N, 7-inch Metal Cutting Horizontal Band Saw
Star Rating
-
Prime Status
-
Preview
Jet HBS-916W 1-1/2 HP 115-Volt/230Volt 9-Inch by 16-Inch Capacity Horizontal Band Saw
Product
Jet HBS-916W 1-1/2 HP 115-Volt/230Volt 9-Inch by 16-Inch Capacity Horizontal Band Saw
Star Rating
-
Prime Status
Preview
Dake SE-712 Model Standard Duty Horizontal Band Saw, 120V, 1 Phase, 63-1/2" Height x 21" Width x 56" Length
Product
Dake SE-712 Model Standard Duty Horizontal Band Saw, 120V, 1 Phase, 63-1/2" Height x 21" Width x 56" Length
Star Rating
-
Prime Status
-
Preview
Baileigh BS-250M Hydraulic Horizontal Mitering Band Saw, 110V, 1.5hp Motor, 1" Blade, 8.93" Round Capacity
Product
Baileigh BS-250M Hydraulic Horizontal Mitering Band Saw, 110V, 1.5hp Motor, 1" Blade, 8.93" Round Capacity
Star Rating
-
Prime Status
-
Preview
3 Speed!!! 1 HP 4 in. x 6 in. Horizontal Vertical Metal Cutting Band Saw FEDEX
Product
3 Speed!!! 1 HP 4 in. x 6 in. Horizontal Vertical Metal Cutting Band Saw FEDEX
Star Rating
-
Prime Status
-
Preview
SHOP FOX W1715 3/4 HP Metal Cutting Bandsaw
Product
SHOP FOX W1715 3/4 HP Metal Cutting Bandsaw
Star Rating
-
Prime Status

View Top 8 Horizontal Band Saws for Metal Cutting, Below-

1. KAKA BS-712N || 7-inch Metal Cutting Horizontal Band Saw

KAKA 7-inch Metal Cutting Horizontal Band Saw

Shocked by KAKA’s home depot form as a metal cutting horizontal band saw production? We also get shocked by innovation. Many customers ask about the specialty and why so being thankful to them. Well, it is about the versatile chopping settings from the toolbox of the BS-712 series.

As we found a high capacity to rip 7” x 12”, similar to the previous vertical/horizontal band saw for metal cutting. Including steel, aluminum and railroad bars. Sounds powerful two-in-one, right? 

Featuring a 4-speed blade is another plus point to elevate your task mode. As this electric horizontal band saw enables quick cuts in numerous shapes. Whether the motor is engineered 1.5 AMP, to tune in a perfect feed rate. Though a perfect feed rate of a metal cutting horizontal band saw relies much on quick clamps. You do not have to worry, because the Hydraulic feed roller will control your project angle at ease. 

Forgot about the portable wheels. That secures transportation of your band saw like clamps do metal at fixed places. By instant rotating from 0 to 45 degrees. At last, the product dimensions 50” x 20” x 45” and 350 pounds give a breeze while working with the notch. 

What we liked

  • Designed for high portability;
  • Instant changing cut-off angles;
  • Act both vertical and horizontal modes.

Disliked

  • Hefty priced;
  • Hard to find the wheel's cam lock.

2. Jet HBS-916W || 9” x 16” Horizontal Band Saw for Metal Cutting

Jet HBS-916W Horizontal Band Saw for Metal Cutting

The 2nd one head as a horizontal band saw for metal cutting, empowered through a range of materials. Designed the most coolant system like a dry metal cutter concludes to protect your fingers. With a complete blade guide that will flow after the relaxation mode.

From JET series, this one comes up with a 9” x 16” rip capacity, works smooth at one phase only. Whether other ones have better swivel power, it can rotate only 0-45 degrees. An integrated tensioning system can make sense on the blade by the built-in gauge and large handwheel. In fact, you have a parallel ball-bearing supporting term.

 Another advantage you can take up is the fully adjustable jaws hydraulic down feed or feed roller. That not only ensures the blade guard, but an auto-shut-off/on valve also. Even if you protect yourself with extra equipment, it renders on its own.   

What we liked

  • A coolant distribution system;
  • Guarded blade;
  • Heavy-duty band saw;
  • Large handwheel.

Disliked

  • Unportable;
  • Not affordable.

3. WEN 3975T || 4-7/8-inch x 5-inch Band Saw for Metal Cutting

WEN 3975T Horizontal Band Saw for Metal Cutting

Searching for a solid horizontal band saw, can cut i-beams too? The right solution with a 6” stand from WEN 3975 series, we have included in our listing.

Integrated beveling blade from the toolbox offers to cut-off anything from 0-60 degrees. Whenever you go to install your handpicked material on the table, adjust at an exact angle until you give it a proper sizing. Whether it is a metal pipe up to 5” or have rectangular sizes up to 5 x 4-7/8 inches. Even you can cut-off more than a 24” metal, at a single pass with a 2-speed blade of 125/260FPM.

Comes up with a storage and transport mechanism. That helps to move it to your desired places. The ball bearing guides allow a reliable operation that you can get along with a long time. Also, provides a long life span by sensing the blade tension system. Even if the tilting knobs tweaks between jobs with a strong grip on your workpiece. 

What we liked

  • 2-speed blade;
  • Affordable;
  • Simple storage.

Disliked

  • Little problematic ball bearing.

4. SHOP FOX W1715 Band Saw for Metal Cutting

SHOP FOX W1715 Horizontal Band Saw for Metal Cutting

Introducing another excellent horizontal/vertical band saw from SHOP FOX manufacturer. Use this economical tool from smaller to larger projects as long as you can.

What makes it more economical and separate from others? You will find the answer in its mobile base and 3-speed blade specialties. Its built-in mobile base provides simple storage system at the corner of your workshop. Also, the mobility will help to transport from here to there. Including the V-belt replacement option to change 3-speed blade 78/108/180 FPM. So, you can change the speed after a stock variety of hard metals.

W1715 sets up super straight cuts, as in vertical positions through the entire pieces.  Of course, who does not want such a pattern and curvy shapes at a single pass. If you want more precise cuts at horizontal position, turn on the stop switch. Whether you want to do it in frequent times, or want consistent results. 

What we liked

  • Adjustable from 0-60 degree angles;
  • Ball bearing construction;
  • Wheels and handles for portability;
  • Easy to get slower and faster feed rate;
  • Automatic shut-off.

Disliked

  • Better for light manufacturing;
  • Flimsy base.

5. FEDEX || 4"x 6" 3 Speed Horizontal Metal Cutting Band Saw

FEDEX 3 Speed Horizontal Metal Cutting Band Saw

Looking for a small workshop manufacturing horizontal metal cutting band saw? FEDEX produced such a small rip capacity 4” x 6” rectangular based, for wood, plastic, steel and tubes at the same time. Even the blade speed and sharpness will amaze you while operating. The blade remains sharp whether you have to cut 200 pieces of metal pipes, or more than that amount. The rapid action from rapid speed does not overheat the ¾ AMP motor either.

Attached metal stand will give you a little flimsy mode. Though works well while you keep your workpiece on the swivel, to vise up 0-55 degree angles with a 14TPI blade. Satisfactory level comes when you have a firm grip on the handle to fix everything in tilting position. Availing enough  gravity feed rate can satisfy you more, when you have it through releasing tension from the spring by twisting the handle.  

What we liked

  • 3-speed blade;
  • Small workshop based;
  • Affordable;

Disliked

  • Dubious stand.

6. Baileigh BS-250M || 8.93" Hydraulic Horizontal Mitering Band Saw

Baileigh Hydraulic Horizontal Mitering Band Saw

Any horizontal band saw heads, to cut-off aluminium and sturdy alloy mitering up to 60 degrees? It is worth mentioning that this one enabled such a mechanism on its own. 

Some other features from BAILEIGH make it stand out. First, built-in inverter driven 2-speed (66/280) blade, you can adjust for several material types. Like faster speed for aluminum and brass types and slower for hard ones. Even this single miter band saw let you cut around 9” round hard stock within a second. But if you are worrying about tidying up your workspace. We suggest you not to do so. Because this one includes an industrial grade coolant pump, collects all chips in it during operations. Besides, it keeps the blade teeth cool and lubricated for long lasting usage with a 1.5 HP motor. Another engineered 3 HP motor from the gearbox, used to drive the inverter for non-stop production. If you want to control production run, two ways integrated most. One is to turn on the hydraulic roller and the second is in two steps. At first, pull down the arm, then trigger the switch of the coolant system.     

What we liked

  • Blade guide: carbide by roller;
  • Square, round and rectangular rip capacity;
  • Chip tray;
  • Quick changing service for mitering angle.

Disliked

  • Small footprint.

7. Dake SE-712 || 21" x 56" Standard Duty Horizontal Metal Cutting Band Saw

Dake SE-712 Standard Duty Horizontal Metal Cutting Band Saw

Last but not least. This horizontal band saw with stand, comes up with the most safety interlock function, worth its title. Other practical safety integrated systems attached from the manufacturer DAKE. Including a metal coolant pump, chip tray and obviously the hydraulic control bar.

The coolant pump not only makes your workpiece dry, but the blade also. Even the heavy steel base floor stand offers such big deals while operating medium-duty applications. Like copper alloys, hard brass, bronze, stainless and some carbon-molybdenum-nickel alloy steel. With a 4-speed blade of 85, 130, 180, and 235 feet per minute (fpm). Besides, the anti-vibration bed 9” x 21” enables better cuts to the top-mounted edges.

If you want to control your feeding rate, the hydraulic controller allows to do so at variable rates. In fact, by locking the system, according to the height and scale of tasks.

What we liked

  • Swivels up to 45 degrees;
  • Low voltage reset;
  • Thermo overload protection.

Disliked

  • ¾ HP motor;
  • Quick rusting out.

8. JET 414459 HVBS-7MW || 7-Inch Horizontal Band Saw for Metal Cutting

JET 414459 7-Inch Horizontal Band Saw for Metal Cutting

Starting with the most popular version from JET makes its way out. We are very grateful for this portable highbred bandsaw. For coming with prior vertical/horizontal functions, only for cutting metals.

This metal cutting horizontal band saw acts quite similar to a vertical band saw does to customize your workpiece, as it remarked in its title. As well as it vises up to 45 degrees at a rapid single phase, even at rush hours, like a best bandsaw for money. The built-in adjustable mechanism stops you while it becomes very harder to continue. Another popular feature that cheered up us is the manual blade speed settings. Until you use proper blades at 4-speed. Like 85, 130, 180 and 285 SFPM, according to your metal samples. Kind a thumb of rule, the harder the metal works well at slow feet per minute. With a perfect rip capacity of 7 x 12 inches smooth.

Featuring with cast-iron is such a fine and perfect making for durability. If you get closer, you may see a coolant system with an auto-shutoff option. This remains your workpiece cool during the heavy workload. But it is mandatory to read an adjustable roller blade guide. To accommodate different materials with a chip tray under the roller to free up your workspace.

What we liked

  • Flexible;
  • Perfect control over each project;
  • Sturdy construction;
  • ¾ powered motor.

Disliked

  • Heavy to transport;
  • Expensive.

Buyer’s Guide - Horizontal Band Saw for Metal Cutting

Portability

The most desired issue that a potential buyer looks for horizontal metal cutting bandsaw. As it comes with the portable wheels, with cam locks to have a secure movement. It does not matter wherever you want to move the band saw, around the shop or inside your garage and at job sites.

Sometimes seems to create problems with 4-wheelers instead of 2-wheelers. Without cam locks, such portable models can roll away by itself anywhere. Ensure the wheel locks while buying the toolbox. If it is not available, find some other way to secure the machine’s portability. 

Table 

How about the table of a horizontal band saw? It matters even for a benchtop bandsaw. Without the heavy-duty table bed, you have to struggle for an efficient straight or curvy cut. In case of repeated chops, you should have more efficiency, to vise up at different angles. While buying, make sure the table height that you can adjust and provides comforts, the scaled works in extended periods reciprocating the speed of your saw blade. As well as a reciprocating saw does.

Power

We are talking about the power of the engineered motor of metal cutting horizontal band saws. Plenty of motors come up with X-torq size. Almost all have equivalent power, for instance, 1.5 HP, 1 HP,  ¾ HP and so on. But some countries take into account the power VOLT limit. Some tend to limit in 115 VOLT or some exceed the range like 230 VOLT. Notice which limit you want to start your crafty projects or the professional one.

Cutting Angles

If you are taking into account the blade speed feature, you should consider the cutting angles too. Except several manufacturers, modern ones are providing from 0 to 60 degrees, even more than this of mitering angle and chopping down proficiency. So you should check if it is worth for money as a potential buyer.

Read more: The 10 Best Angle Grinders Reviews

An added remarking feature in its mechanism is how angles should change while dealing with a big or small project. Remember, the quicker the vice releases up, the better the horizontal band saw is.

Safety Features

All important safety functions you may not find while evaluating a horizontal band saw at stores. Some manufacturers may attach blade guides, coolant pumps, safety switch and hydraulic bar too.  

The guide enables us to have a precise and smooth cut, with an easy to adjust feature to fix your workpiece at the proper place.

The coolant lubricant not only hinders the overheating of the blade while moving, as well as the machine. This integrated method supposed to keep the metal cool before and after ripping by the band saw.

The safety switch, keep apart the saw from being in an auto-engagement with power. So you do not have to worry while comforting yourself in-between the task.

Final Thoughts

The above-described metal cutting horizontal band saws are trendy and competing each other. We know that you want to run with the trend as well everyone does. Are not we right?

Yeah, but before buying one in store, remember the considering points. For instance, pricier side, adjustments, user-friendliness and extra features. Hope the best for having the right decision.

Leave a Comment