A small tree is defined to be a species of full-grown tree which usually grows in height not less than 15 feet and a maximum height might reach up to 24 feet with maximum spread of 24 feet endorsed by the botanists. Sometimes we need to fell trees for various reasons.
There are few unique techniques that applied to fell a small tree in a safer way to avoid workplace hazard and inappropriate way of felling.
The most important aspects include preparing a feeling spot examining all safety aspects, using right saws and right technique to cut down the tree. Creating notch at a right position of the tree is another key aspect to keep in mind.
You must make sure you have enough grip to hold your tree firmly while felling takes place. Eco-friendly aspect has to be taken into account before cutting down your tree to protect environmental safety.
However, I have designed this article to discuss in details how to cut down a small tree with a saw to make you familiar with techniques before commencing your tree felling project.
Techniques of Cutting Down Small Tree Using Saws
As I said few basic techniques you must adhere to before and during cutting down trees. Post cutting aspects are also vital for safely accomplishing your tree felling project. Always gather all materials that you need to cut down your trees.
Below are the safest and simplest ways you should follow through for cutting down trees. Be trained on creating notch at the right spot of the tree for safer felling.
Wear Safety Equipment
For felling tree wear all safety equipment including helmet, eye-protective goggles, boots, and jacket to prevent hazard and injuries at tree felling site.
Examine Tree Felling Area
Examine carefully around the felling area to ascertain there is no structures, electric wares, by-pass road or other trees which might cause inconvenience for your project tree to fall safely.
Make sure the felling environment is completely safe before cutting down your tree. Also check out vigilantly if there is any debris and clean the felling site to avoid hazardous environment.
Determine the Leaning Direction and Stability of the Tree
It’s important to determine where the tree stands out sturdily, if it’s quite stable and healthy etc. as these aspects impact on safer falling of the tree.
Another safety aspect is to consider the tree’s leaning direction. Leaning direction significantly leads the tree to fall down to the certain direction as the tree itself is not able to change its own direction while falling down.
Ascertain Falling Path
Another important aspect to ascertain that there is no structure, trees, power lines, or roads around the falling path so that the tree can fall safely without hitting anything around.
In this step, do some calculation including height of the tree and distance between the base of the tree and falling area. This measurement would prevent all types of hazards during felling of the tree.
However, you should also create a small notch on the side of the tree to get your tree inclined towards falling direction for falling safely. If your tree is loaded with too many branches, it’s good to cut down them at the beginning to free your tree.
Determine Exit Way During Falling
Determine exit area so that you can escape to the safe distance while the tree falling takes place. It’s a vital task to prevent accidents and injuries. Never walk over or stand near the tree when your tree starts falling after cutting down.
Felling Tree With Chain Saw
The first task is to make a notch on the tree at 70 degree angle considering the felling direction of your tree. Make sure the notch maintains the proper measurement so that your chainsaw will be able to cut on the notch.
The notch must be 1-2 feet off the ground. After that, take a chainsaw, hold it tightly with both hands to have strong grip and cut on the notch exactly at 70 degree angle and fell the tree successfully.
You can also make horizontal cut at the base of the notch if you want to keep the bottom of the tree straight.
You can also make a bore cut by inserting the tip of the saw blade through the tree instead of making a cut from the side of the tree.
To produce the bore cut, position your chainsaw blade 1-2 inches away from the border of the notch and push it thoroughly through the tree. Then keep sawing from the back side of the notch until achieving horizontal cut through the other end of the tree.
Felling Tree With Hand Saw
For producing a horizontal cut with the hand saw, place the teeth of handsaw 1-2 feet above the roots of the tree and move it in horizontal motion through the tree. Keep going until one-third of the way is made through. Two-handles saw would be helpful and one assistant to do this.
However, hold the saw with both hands to cut the tree. After horizontal cut, start hatching above the cut to make a notch. For doing so, hold the hatchet with both hands and run the hatchet in vertical motion into the side of the tree at recommended angle and keep cutting until a defined notch becomes visible.
After that, cut the tree all through using the saw from the back side of the notch. During falling, stay at safer distance to avoid injuries.
I hope you are familiar now about the essential aspects of felling trees and quite confident to do it yourself for your project. The key equipment including saws, hammer, hatchet and few other accessories you should gather beforehand for smooth operation of your tree felling project. Employ someone to assist you while accomplishing your project.
Take care of environmental safety aspects while going through the felling process. Maintain all other safety protocol to avoid workplace hazard and injuries.
Application of proper techniques for tree felling project needs adequate training and practice. Starting with cutting down small trees would make you expert overtime and one day you too might be quite capable of dealing with tall tress felling project.
I would always expect you to share your comments and feedback which is really helpful for us to optimize our service to make it more pro-client. If you share this articles and our website with your family and friends, it could create a path for us to meet more people in coming days and bring them under umbrella of our excellent clients’ services.
Last Updated on February 16, 2021 by John Dylan
I am John Dylan. I have a clear experience of different types of tools since my childhood. I started my career as a handyman at a construction company. Later on purpose, I had to work as a plumber, and electrician also.
So I had to research and explore different tools for my own good. In toolsscore I try to share my findings. I attempt to help people find the right tool. Hope it helps.