How to Remove Sunken Nails From Wood: Easy Techniques!

Nail and hammer are widespread frequently used tools particularly during implementing house renovation or similar kind of projects. Nails are drived in the workpiece with the hammer or other tools including nail guns. During home improvement project sometimes you may face a situation when you need to pull out the sunken nails. Though removing nail is not that much difficult job, but as it deals with your precious wood materials, it may damage your piece if proper techniques are not followed to prevent such incidence. 

You may even sometimes find an extremely stubborn nails deeply buried into your materials which sometimes needs couple of ways to remove. 

There are some smart techniques that you need to know while dealing with removing sunken nails from wood efficiently protecting your wood to be in original state. 

Therefore, I have designed my article to discuss how to remove sunken nails from wood so that you can get familiar with the rights techniques and apply them while dealing with nail removal tasks.  

how to remove sunken nails from wood

Techniques to Remove Sunken Nails From Wood

As I said, removing nails involves some basic aspects which you need to be acquainted with to protect your workpiece from damage.  There are standard nail remover tools and accessories available in the market and each of them has different function to efficiently deal with the removing task. Besides, few more technical aspects you need to care for during and post nail removal task. 

Claw hammer, pry bar, cat’s paw, reciprocating saw and few others are the common tools the woodworkers use to remove nails. Each of the tools is used to tackle different situations in the event of buried nails. Sometimes part of the nails may need to be cut partially that protrude from the materials to resolve the issue. 

You have to carefully review the situation and then choose the removal options so that it would give you the best result. 

Safety First!

Maintain safety protocol while dealing with nail removal task to avoid accidents and workplace hazards. Wear all PPE like goggles, standard gloves and boots, etc. to be protected from injury. 

Get a block to use during nail removing task. Place the block under the tools to have enough leverage for proper positioning of your nail removing tools and achieving efficient removal task. 

Remove Nail With a Hammer

remove nail with a hammer

Credit: Photo: ronaldphillipsantiques.com

Hammer may not be the good choice to remove nail, but it won’t be a bad option when there is no other better tool at your hand to pull out the sunken nails. However, you need a claw hammer

claw hammer

Process to Follow:

  • First identify the nails you want to remove. 
  • Take your hammer and position it to the head of the nail. Then start prying gradually and repeat it until the head of the nail appears on the wood surface.
  • Then get a tight hold on the nail’s head and make a sideway with a slight pressure. Don’t put too much pressure to avoid damage of your wood piece. Repeat it until the nails is pulled out completely.     

The above method may not work in case of deeply buried nails. In that case, there are some other effective methods that will be discussed later. 

Remove Nails With Cat’s Paw Pry Bar

remove nails with cat’s paw pry bar

Credit: Photo: jimthetoolman.com

In case of using pry bar, you don’t need a block or nay other support. However, pry bar is little risky tool which can even permanently damage your wood surface. However, pry bars actually is a brilliant nail removing tool for removing bent and galvanized nails which hammer can’t do. 

Process to Follow:

  • Get your cat’s paw pry bar and position it as closer as possible at the end point to the nail which to be removed. Then pick your hammer and use that to push the pry bar into the wood.   
  • Then simply pull out the nails with the pry bar as long as you need it to finish your task.  

Remove Headless Nails

Removing headless nails need different technique to apply. The above methods discussed earlier with claw hammer or Cat’s paw pry bar won’t work in this case. So let’s see how you can remove the headless nails of the wood surface. 

To tackle this problem, a pair of needle-nose pliers and diagonal-cutting pliers would be a good option. As the nail is headless, you won’t find any area to grab the nail. Therefore, you can have a good grip over nail with the pliers. 

Process to Follow:

  • Place your needle-nose pliers as near to the nail as possible and dig out small amount of wood to make a path for the nail to be pulled out. After having the path, grasp the upper tip of the nail with the plier.
  • Then start pulling the nail out of the wood. Keep your plier straight as much as possible while removing task taking place to avoid any obstruction in the middle of the task. To release the tight grip of the nail, you should slightly move the nail side to side so that the nail can have the easy path to come out. 
  • Continue this task until the segment of the nail is raised above the wood surface. 
  • When the headless nail got exposed from material, you may replace it with the diagonal-cutting pliers. Don’t grab it onto the nail too strongly to avoid cutting the nail in the middle. Just grab on to the nail in a way so that the plier becomes able to move it around. 
  • At this stage, repeat the same motion you did with the needle-nose plier. Move the nail side by side until the portion of the nail is pulled out slowly. Again, don’t put too much pressure to prevent the cutting of the nail. 
  • Finally pull out the nail when most of the portion of it is removed. 

Remove Nails Using Reciprocating Saw

reciprocating saw
  • Reciprocating saw you may use to pull out the nails as it can cut with precision. This tool can reach to the closest point of the nails into wood to pull it out. But the demerit is if you are not quite familiar with this tool, you better avoid this to prevent any damage on your wood piece.
  • If you are ready to use reciprocating saw, get 10-teeth per inch blade. They are extraordinarily brilliant to cut through nails. 

Remove Nails Using Nail Kickers

remove nails using nail kickers

Credit: Photo: YouTube.com

Nail kicker is one of the effective nail removing tools. Though the setting up is little consuming, but it would give you the best service once you successfully have set it up. This tool will make the removing task quicker and smoother compared to other ones without damaging your workpiece. Let’s look at the process

Process to Follow:

  • Prepare your wood from where nail is to be removed
  • Place the nail kicker on the nail’s head and push it slightly through the wood surface
  • Then the tool will automatically pull out the nail with its own capacity
  • In case of unsuccessful, repeat the method until the entire nail is removed. Else, you can also prefer other methods to remove the nails depending on the situation. 

Remove Nails With Nail Jack

Nail jack also could be a solution for nail removing task. It’s pretty handy tool to help in removing nails

Nail Puller

Process to Follow:

  • Place the nail jack in the correct position where the nail is buried.
  • Drive the nail jack into the head of the nail and hold the head
  • Then squeeze and amalgam it into the nail. The nail will smoothly come out. 

Additional Tips

During nail removing jobs, you would notice some removing marks or holes left and sometimes they are too small to notice. But they may affect the appearance of the wood surface. Fill up the holes with some spackle and leave it for few hours until spackle dried off. Then sand them down and paint over to retrieve the original state of your workpiece. 

Final Notes

I hope you have found this article beneficial while you have to deal with sunken nails to remove. It’s pretty simple but little tricky as it might damage your wood piece if you won’t take extra care and apply recommended techniques to carry out buried nails removing jobs. If needed, consult with the experts while working with costly materials related to sunken nails removal. 

Knowledge is power. Train yourself to work efficiently for the best results avoiding occupational hazards and accidents. Keep yourself updated with latest information in the technology world to sustain your productivity and professionalism. If needed, consult with them to be guided properly. 

Never ignore the safety protocol to maintain as it may cause injuries and fatalities. 

Finally, I would expect you to share your comments and feedbacks how it helped you and if you need further consultations. Please help us share this article and our sites with people you know so that we can offer our expert services to address the challenges people are facing in the power tool industry.  

Leave a Comment